Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Glendale?
Gate repair in Glendale typically costs between $150 and $900, depending on whether the problem is mechanical or in the operator and control board. Simple fixes like a realigned latch, a replaced hinge, or a new remote receiver usually land at the low end, while motor replacement, control board swaps, and track or roller rebuilds push toward the high end. Electric and automated gate repairs in Glendale generally run $200 to $1,400 when the motor, wiring, or safety sensors are involved.
We’re a dedicated gate specialist, not a general handyman outfit that takes gates on the side. Our technicians have up to 12 years of experience, we work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, and every estimate is free. Call (855) 632-1674 and we’ll get a real number in front of you before anyone touches the gate.
Key Takeaways
- Most residential gate repairs in Glendale fall between $150 and $900.
- Electric and automated gate work runs $200 to $1,400 depending on the component.
- Diagnostics are the difference between a $200 fix and a $1,200 replacement. We repair first.
- Free estimates, free written pricing, no service-call fee.
- We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Repair Cost Breakdown (2026)
These are typical estimated ranges for the Glendale market in 2026. The written estimate you receive after we look at the gate sets the final price. Nothing is billed by guesswork.
| Repair Type | Typical Cost Range (Glendale, 2026) |
|---|---|
| Basic mechanical adjustment (latch, hinge, stop, alignment) | $150 – $280 |
| Roller, track, or track-rail repair on a sliding gate | $200 – $450 |
| Gate panel repair or re-hang | $250 – $600 |
| Operator motor repair or replacement (residential) | $450 – $950 |
| Control board replacement or reprogramming | $250 – $550 |
| Safety sensor and photo-eye repair (electric gate) | $150 – $350 |
| Wiring and low-voltage fault diagnosis (electric gate) | $200 – $500 |
| Keypad, remote, or entry device repair | $120 – $350 |
| Full automated gate diagnostics and repair (residential) | $250 – $1,400 |
| Commercial automated gate repair | $350 – $2,500 |
Two things push a repair up: the operator and the control board. A mechanical fault on a swing gate is usually straightforward and inexpensive. An automated gate that won’t open is a different job, because the fault could be in the motor, the wiring, the board, the sensors, or the power supply itself. Our technicians arrive ready to diagnose from the motor to the control board rather than guessing at the first brand they know. That focus is what keeps a $300 sensor issue from turning into a $1,200 motor quote.
The lower end of the range covers jobs where the part is cheap and the labor is short. Alignment issues, worn rollers, loose hinges, and mis-set stops are quick fixes when the technician knows what they’re looking at. The upper end covers commercial operators, heavier slide gates, and any situation where a motor or board has to be sourced and swapped. We don’t add a fee for coming out, and the estimate is free either way.
What Affects Gate Repair Pricing in Glendale
Pricing on a gate isn’t one-size-fits-all. Here’s what moves the number:
- Mechanical vs. electric. A mechanical fault on a manual gate is the cheapest category. As soon as the operator is involved, the diagnosis deepens and the price range widens. Electric gate repair is a named core service for us, not something we outsource.
- Gate type and weight. A lightweight residential swing gate is easy to work on. A heavy slide gate, a wrought-iron panel, or a gate on a slope requires more careful handling and can add labor. Glendale yards with stone and masonry columns sometimes hide track and footing issues that only show up on the inspection.
- Brand and controller. Some controllers are easier to work with than others. We’re brand-agnostic and we know the majors, so a LiftMaster board doesn’t confuse us any more than a FAAC or DoorKing board does. If you have a Viking or Ghost Controls system that other companies pass on, we work on those too.
- Parts availability. Most common components are available quickly. Less common parts, especially on older or discontinued operators, may take longer to source and can affect the final number.
- Access and location of the operator. A gate motor buried under landscaping or set in a tight corner takes longer to reach and test. Clearing the access before we arrive shortens the visit.
- Whether it’s a repair or a replacement. Sometimes the right call is a repair. Sometimes the motor is finished and a replacement makes more sense financially. We lead with repair first and only recommend a replacement when the repair cost doesn’t justify it.
None of these factors is guessable over the phone. The written estimate after an on-site look is the number that matters, and it’s free. Call (855) 632-1674 to book a visit.
What a Typical Gate Repair Visit Looks Like
In Glendale, the gate has to survive summer heat. Metal panels expand, plastic housings on some operators get brittle, and control boards that were fine in spring can start throwing faults when the temperature climbs. We see more sensor and board issues in the hotter months, and more mechanical issues after a monsoon gust has pushed a panel out of alignment.
A visit usually moves through four stages. First we watch the gate cycle. We want to see how it moves, where it stalls, and what the operator does when it hits an obstruction. Second, we check the mechanical side: hinges, rollers, tracks, stops, and the gate’s alignment. Third, on an automated gate, we test the operator, the control board, the safety sensors, and the low-voltage wiring. Fourth, we put the findings into a written estimate with a clear range and a clear recommendation. If it’s a repair, you get a repair price. If the motor is beyond saving, we tell you and we tell you why, and we don’t push a brand switch you don’t need.
Heavy gate panels and the wiring that feeds an automated operator are not things to handle without training. The operator’s power supply and low-voltage wiring can cause serious injury if you don’t know what you’re testing, and a heavy slide gate that comes off its track can crush a person or a vehicle. This is a job for a trained technician. Don’t open the operator housing or touch the wiring yourself.
How to Save on Gate Repair
- Fix the small stuff before it becomes big. A gate that drags or hesitates is telling you something. A $200 track adjustment today is cheaper than a $900 motor replacement later.
- Get a written estimate and compare the diagnosis, not the total. Two quotes with different diagnoses aren’t the same repair. Make sure each quote names the actual faulty component.
- Clear access to the operator. Trim back landscaping around the motor and control box before the visit. You’ll spend less on labor.
- Test the safety sensors yourself. If the gate reverses for no reason, check that nothing is blocking the photo-eyes (a leaf or a spider web is enough). If they’re clean and it still reverses, that’s a fault for us, not for you.
- Repair before you replace. We repair first. If a technician from another company quotes a full replacement on a gate that’s only a few years old, get a second opinion. Our gate repair service starts with a diagnosis, not a sales pitch.
- Know your brand. Tell us the operator brand when you call. LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule are all in our wheelhouse, so you won’t get the “we don’t work on that” answer.
Every estimate from us is free. There’s no service-call fee and no diagnostic fee, and the price we write down is the price you pay. Call (855) 632-1674 for a free estimate.
When to Repair and When to Replace
Most gate problems are repairs. A worn roller, a misaligned latch, a failing sensor, a control board that’s lost its programming, a motor that’s drawing too much current because the gate is binding. Those are fixes, and they usually cost far less than a new gate or a new operator.
Replacement starts to make sense when the operator is at the end of its service life and the repair quotes are stacking up, or when a part is no longer available and the whole controller has to be swapped anyway. A gate that’s been damaged structurally, where the panel is bent or the frame is cracked, may be beyond what a repair can fix safely. The honest answer is that the decision depends on the gate in front of us, and a written estimate is the only way to make it with real numbers. That’s why we inspect first and quote second.
Who We Are and What We Work On
We’re a full-service gate specialist. That means we handle gate repair, electric gate repair, and gate installation as our three core services, and we don’t drift into garage doors, fencing, or general handyman work. The focus is the gate.
Our technicians have up to 12 years of experience, and we service nine of the most widely installed gate operator brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Being brand-agnostic matters. It means we’re not locked into one manufacturer, so our recommendation is driven by what the gate actually needs, not by which brand a technician is trained to sell. If your system is a Ghost Controls or a Viking that a general repair company turned down, that’s a normal job for us.
If you’re starting from scratch, our Gate Repair Glendale page covers the full range of what we do, from a single hinge to a brand-new automated installation. You get one point of contact for installation, repair, and ongoing work on the same gate.
FAQs – Gate Repair Cost
How much does a gate repair cost in Glendale?
Most gate repairs in Glendale cost between $150 and $900, with simple mechanical fixes at the low end and motor or control board work toward the top. Electric and automated gate repairs generally run $200 to $1,400. Call (855) 632-1674 for an exact quote, free of charge.
Is it cheaper to repair or replace an electric gate operator?
Repair is almost always cheaper, and it’s where we start. A control board or sensor repair typically runs $250 to $550, while a full operator replacement runs $450 to $950 on the residential side. Replacement only makes financial sense when the motor is at the end of its life and parts are no longer available. Call (855) 632-1674 and we’ll tell you which one your gate actually needs.
How much does an electric gate repair cost in Glendale?
Electric gate repair in Glendale typically runs $200 to $1,400 for residential systems and $350 to $2,500 for commercial ones. The range depends on whether the fault is in the sensors, the wiring, the control board, or the motor. We diagnose from the motor to the control board before quoting. Call (855) 632-1674 for a free estimate.
Can you come today?
Same-day service is available for many gate repairs in Glendale. Call (855) 632-1674. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening.
Do you charge a diagnostic fee?
No. Our estimates are free, and there’s no service-call fee or diagnostic fee. The written estimate you receive after we look at the gate sets the final price, so you know the number before any work starts. Call (855) 632-1674 to book your free estimate.
Do you work on my gate brand?
Yes, for nine of the most common brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We’re a dedicated gate specialist, so the system in front of us gets a proper diagnosis rather than a shrug. Call (855) 632-1674 and tell us what you have.
Get Your Free Gate Repair Estimate
Gate repair pricing in Glendale depends on the gate, the operator, and the fault, and the only way to get a real number is for a technician to look at it. Our estimates are free, our pricing is upfront, and we repair first. Call (855) 632-1674 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Glendale market as of 2026. Gate Repair Glendale offers free estimates – call (855) 632-1674.
Written by the team at Gate Repair Glendale.
What Our Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Paige Vaughn"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Alicia Ellison"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Lamont Bryant